几乎所有嵌入式平台的行业标准
IDC20Adebug probe 最初设计用于调试采用 Arm® CoreSight™ 调试基础架构的 SoC。由于Arm 架构 的巨大成功，这一调试概念成为嵌入式市场多核系统事实上的调试标准。
如今，IDC20Adebug probe 支持各种架构 和协议，可调试带或不带 CoreSight™ 的 SoC，是劳特巴赫最成功的debug probe 。
Arm/Cortex
安第斯核心
APEX
APS3
ARC
AVR8
ARP32
超越
C166SV2
C2000
C5000
C6000
C7000
CEVA-X
HC11
Hexagon
i8051
M32R
梅塔
Mico32
MicroBlaze
NIOS-II
PRU
RISC-V
SDMA
SH
SRP
星核
STM8
STRED
Synopsys-ASIP
柚木/柚木灯
Ubicom32
Xtensa
ZSP
78k
获取适合您的 IDC20A 探头架构
IDC20A Debug Probe with debug license to debug Cortex-M cores (Armv6/7/8-M) and SecurCore SC000/SC300, via JTAG, cJTAG (IEEE 1149.7), or Serial Wire Debug (SWD). Includes licenses to debug and trace Cortex-M cores and SecurCore SC000/SC300, as well as debug GTM and IPU cores. Includes TRACE32 software for Windows, Linux and macOS on DVD or via download. With legacy debug modules LA-7702/LA-7704 only JTAG is supported. Voltage range 0.4V to 5.0V.
IDC20A debug cable for 64-bit RISC-V cores (RV64) usable with a PowerDebug base module supporting JTAG, cJTAG and Serial Wire Debug Port (0.4 - 5.0V). Includes license for multicore debugging. Includes TRACE32 software for Windows, Linux and macOS on DVD or via download. Requires TRACE32 software R.2020.09 or newer. Requires a PowerDebug base module. A range of converters are available to adapt to different target connectors (including MIPI pinouts).
支持 Tensilica 的 Xtensa 内核 通过ARM JTAG 接口 包括 TRAX（内核逻辑中的跟踪 RAM）的内核跟踪解码 包括用于 Windows、Linux 和 MacOSX 的软件 需要电源调试模块 IDC20Adebug cable 如果使用 14 引脚 JTAG (Xtensa) 连接器，则需要 LA-3763
通过ARM JTAG 接口支持 Tensilica 的 Xtensa 内核 包括用于 TRAX（内核逻辑中的跟踪 RAM）的内核跟踪解码 IDC20Adebug cable ，支持 5 引脚标准 JTAG、cJTAG（IEEE 1149.7）和串行导线调试。 (IEEE 1149.7) 和串行线路调试 (SWD)，（0.4V - 5V） 包括适用于 Windows、Linux 和 macOS 的软件 需要 PowerDebug 模块 如果使用 14 针 JTAG (Xtensa) 连接器，则需要 LA-3763
IDC20A debug cable for 32-bit ARC cores from Synopsys inlcuding ARC EM, ARC HS3x/4x, ARC EV/VPX/NPX, ARC 600/700, ARCtangent-A4/A5 usable with a PowerDebug base module supporting JTAG, cJTAG and Serial Wire Debug Port (0.4 - 5.0V). Includes TRACE32 software for Windows, Linux and macOS on DVD or via download. Requires a PowerDebug base module. For ARC-V you require a RISC-V probe instead (LA-3200 or LA-3201).
IDC20A debug cable for Hexagon DSPs and NPUs from Qualcomm usable with a PowerDebug base module supporting JTAG, cJTAG (IEEE 1149.7) and Serial Wire Debug Port (SWD). Voltage range 0.4V to 5.0V. Includes license for multicore debugging and trace decoding. Includes TRACE32 software for Windows, Linux and macOS on DVD or via download. Requires a PowerDebug base module.
IDC20A Debug Probe with a license for debugging of C28x and C29x microcontrollers via JTAG, cJTAG (IEEE 1149.7), or Serial Wire Debug (SWD). Includes licenses to debug Control Law Accelerator (CLA). Includes licenses for onchip trace "PC Trace". ("PC Trace" supports up to 128 program branches.) Includes TRACE32 software for Windows, Linux and macOS on DVD or via download. Requires a PowerDebug base module. Requires LA-3780 if you need to adapt to a TI-14 or TI-20-Compact target header. Voltage range 0.4V to 5.0V.
支持 C6xxx。 使用 IDC20Adebug cable 、 支持 5 引脚标准 JTAG、cJTAG（IEEE 1149.7）和 串行线调试 (SWD)，（0.4V - 5V） 包括用于 Windows、Linux 和 macOS 的软件。 需要 PowerDebug 基本模块。 如果使用 14 引脚 TI 目标适配器，则需要 LA-7748。
支持 C7000。 使用 IDC20Adebug cable 、 支持 5 引脚标准 JTAG、cJTAG（IEEE 1149.7）和 串行线调试 (SWD)，（0.4V - 5V） 包括用于 Windows、Linux 和 macOS 的软件。 需要 PowerDebug 基本模块。 如果使用 14 引脚 TI 目标适配器，则需要 LA-7748。
连接到每个目标
嵌入式应用中有许多不同的连接器。我们拥有多种转换器，可适应相应的连接器。
Converter from an IDC20A debug connector to a MIPI10 or MIPI20T connector. It is designed to connect the Lauterbach IDC20A Debug Probe to a MIPI10 or MIPI20T connector on the target. For a board with a MIPI20D connector (with TRST and RTCK) you require converter LA-3770 instead. Find out about the difference between the two converters at https://support.lauterbach.com/kb/articles/la-2729-vs-la-3770 Note: This converter does not connect the trace pins of a CoreSight MIPI20T connector since they are not used by IDC20A debug cables. Whereas tracing via SWO/SWV is supported.
Converter to connect an IDC20A debug cable to a target with MIPI34, MIPI20D, or MIPI10 connector. For connecting an IDC20A debug cable on a PowerTrace Serial use the converter LA-2770 instead. (LA-2770 is for a MIPI34 connector with pin 1 on the right sight, while LA-3770 expects pin 1 on the left side at the target.) For a board with a MIPI20T connector (with pins for off-chip trace) it is recommended to use the LA-2729 converter instead to avoid driver conflicts. Find out about the difference between the two converters at https://support.lauterbach.com/kb/articles/la-2729-vs-la-3770 Alternatively, you can connect to a board with MIPI20T connector by opening J101 and J102 on this converter to avoid driver conflicts, as described at https://repo.lauterbach.com/pdf/app_arm_target_interface.pdf
Converter to connect a Debug Cable to a TI-14 or TI-20-Compact connector which is used on many targets with processors from Texas Instruments
Converter to connect an IDC20A Debug Cable to a TI-14 connector which is used on many targets with processors from Texas Instruments
Converter to connect the IDC20A Debug Cable to a Mictor connector on the target providing both debug and trace signals. This is needed if you want to connect the Debug Cable without a Preprocessor and if there is only a Mictor on the target.
Converter to connect an IDC20A Debug Cable to a standard 6-pin "Pmod™ " connector. “Pmod™” is a trademark of Digilent Inc.
Converter to connect an IDC20A Debug Cable to a MIPS-14 connector on the target
Adapter to connect an IDC20A debug probe to a classic 14 pin debug connector for Xtensa.
寻找其他调试探头
如果 IDC20ADebug Probe 不适合您，我们还提供其他各种调试探头。
